Quantcast
Channel: Reprap Forum - RepSnapper
Browsing latest articles
Browse All 64 View Live

Re: repsnapper and gen6 help

I'm not sure I can give you a reason immediately for things not working, but perhaps I can make some suggestions. Ignore the M105 command (switch of temp monitoring in RepSnapper). It is RepSnapper...

View Article



Re: repsnapper and gen6 help

Well, Your help did help point me in the right direction... I was using Merlin firmware, but seems this might have been my issue all along.. I reflashed my gen6 with Sprinter, changed the baud to...

View Article

Re: Beginner troubles

Hey Skypuppet, I too have been playing around with computers since the early days. My first computer was a Dick Smith VZ300. How did u go with your repsnapper install? I just wasted over 1 hour trying...

View Article

Re: repsnapper and gen6 help

I hope someone on this forum can help. I have pronterface, and replicatorg running fine but want to check out repsnapper as well but can't seem to get a straight answer anywhere on the net. I have...

View Article

Re: repsnapper and gen6 help

Greg, you need to compile it. Depending on your OS, follow the instructions on github. However, the caveat is that it seems to only run well under Linux. Honestly, it's a real shame how difficult...

View Article


Something off with G-code and Repsnapper

Hi everybody, So, we got our Techzone LC Mendel up and sort of running... We are having problems with some stl. files not converting properly to G-code. What happens is that the Z-axis information...

View Article

Re: Something off with G-code and Repsnapper

Could you attach one of those STL here please ?

View Article

Re: Something off with G-code and Repsnapper

Bonjour DeuxVis, Here is one of the STL files that I tried converting into Gcode with both Repsnapper and Slic3r. I am not a Gcode expert, but when looking at the Gcode that came up in Repsnapper, it...

View Article


Re: Something off with G-code and Repsnapper

I tried slicing it with Slic3r (version 0.7.0) and it does produce Z movements. Repsnapper gcode production is currently not very popular, I can't say if it works as I haven't tried it, but you may...

View Article


Re: repsnapper and gen6 help

Guys I have exactly the same problem, where I can find loader and firmware for GEN6 electronics? I have ALL STAR model printer should firmware be different, or once I upload new firmware the printer...

View Article

Re: Something off with G-code and Repsnapper

F110 might be too fast for your system. Change from "110.0" to "30.0". If that works then find out what the maximum speed is that your z-axis can handle. Try 60, if that works try 80 otherwise try 45...

View Article

Re: Something off with G-code and Repsnapper

Thanks Deux-Vis -we are looking to get away from Repsnapper, but it is the only thing that works right now with our infamous Techzone LC Mendel! We are getting the parts together for a Prusa Mendel...

View Article

Compiling repsnapper in puppy lucid

Hi Im trzing to compile last version on lucid puppy linux. (on NB with 256MB RAM). I think i have installed all needed libraries, but stil i have error during make. Any sugestions, what im missing?...

View Article


Re: repsnapper and gen6 help

I have the model down from you i think, i have firmware problems, did u get it from 3dstuffmaker?

View Article

Re: Repsnapper Extruder Heat Issue

I have the same issue with a stuffmaker running redsnapper, extruder heats up but when run the moniter stops working and heat of extruder drops then heats up and moniter works when paused or on idle....

View Article


Re: Compiling repsnapper in puppy lucid

did you run ./autogen.sh ?

View Article

RepSnapper - Extruder speed

HI, A dumb question, but as I am clue less thought it is better to ask:S In the RepSnapper - Print menu where the extruder length and speed are given, what is the lenght mean - is it mm or cm? Dinesh

View Article


What is the Parameter E in the G-code of Repsnapper?

Hi, i am very new to this software Repsnapper. After loading the stl file, and converting into the G-code i am able to get the G-code. but in G-code What is the Parameter 'E' indicates. can any one...

View Article

Re: What is the Parameter E in the G-code of Repsnapper?

It's the mm of filament the extruder extrudes, either per command ("relative E-code") or cumulative

View Article

Re: RepSnapper - Extruder speed

it's mm, everything is in mm

View Article

Re: RepSnapper - Extruder speed

Thank you. slowly getting used to the things...

View Article


altering repsnapper to directly adjust esteps per mm

I know its kind of a goofy question but I was wondering if anyone has tried to add a direct Extruder esteps per mm adjustment control to any version of repsnapper or any of the host softwares could be...

View Article


Re: altering repsnapper to directly adjust esteps per mm

If your firmware supports it, the gcode M92 with an E parameter can do this. The host software only need a way to send gcodes manually then (repsnapper can).

View Article

Re: What is the Parameter E in the G-code of Repsnapper?

E codes are used during Printing progress It denotes how much length of PLA or ABS to be extruded during Printing Initially E codes are set to E0 E1.0000 denotes extrusion of 1mm PLA/ABS if you need...

View Article

Re: altering repsnapper to directly adjust esteps per mm

Try with Extrusion Multiplier in Printer settings and convert to Gcode Extrusion Multiplier - 1 denotes actual length Extrusion Multiplier - 0.5 denotes 50 % of actual length If your Machine Extrusion...

View Article


Re: repsnapper and gen6 help

Firmware should be open source and you can get it in reprap Firmwares like Marlin, Teacup supports Gen6 you can download it and use it

View Article

RepSnapper with PyCam

Hi all, I'm playing around with a Mendel with the idea of using it to cut vinyl, I'm using PyCam to create the G Code which works well. What I want to know is if i load that into RepSnapper will it...

View Article

Re: RepSnapper with PyCam

It should work, as repsnapper will just stream the Gcode to the board, and marlin or other firmware should interpret it normally as it's mostly G1 moves (I guess, from my experience where we used a...

View Article

Adding more libraries

I'm working on making a copy of Repsnapper that inputs another filetype of 3d models, but I've hit a wall of sorts. I've got everything changed in the code, correctly as far as I can tell, but I can't...

View Article



Re: RepRap Mendel with 6 gen electronics shift Y axis each layer ...

for me this was the belt climbin up the side of the gear (I have metal gears) and shifting by exaclty one belt tooth every time it hapened. It seemed to be speed dependent and only happened...

View Article
Browsing latest articles
Browse All 64 View Live




Latest Images